Skip to main content

Error 49.FF81 on HP 4100mfp and 9000mfp series



 MAJ 02/09/15

For solving error code 49.FF81, verify printer functionality:
  1. Power off the MFP and remove the EIO hard disk. To remove the hard disk remove the two screws from the EIO1 or EIO2 slot on the back of the MFP (depending on which slot the hard drive is installed in). Power up the MFP (turn it on), it will boot up with the message " HARD DISK NOT INSTALLED, COPY AND SEND DISABLED."
  2. Print a Configuration Page by performing the following:
    1. Press the Menu key until Information is shown on the display, then press the Select key to highlight the Information Menu.
    2. Highlight Print Configuration and press the Select key.
    3. The MFP should print out two pages.
  3. Test the MFP by send several print jobs over the network to the MFP from a PC.
  4. If the MFP prints the test print jobs successfully, power down the MFP and reinstall the hard drive. Proceed to the next section and perform a Disk Init.
  5. If the MFP fails to successfully print any of these tests then contact HP Support for further assistance.

How to perform a Disk Init:
  1. Power off the MFP.
  2. Reinstall the EIO hard drive in the EIO slot, and tighten the screws.
  3. Press and continue to hold down the START button on the control panel of the MFP. While holding it down, power up the MFP.
  4. Continue to hold down the START button until the MFP initializes and the three control panel LEDs are all lit up solid. Now release the START button.
  5. Press and release the LEFT navigation button. The message INITIALIZE DISKS will be displayed on the control panel display.
  6. Press and release the SELECT button. Two rows of asterisks will be displayed on the control panel display.
  7. When the asterisks disappear and the message READY appears on the control panel display, the issue should be resolved.
  8. If the 49.FF81 errors reoccur or the MFP hangs while performing the Disk Init procedure, then contact HP Support.

Comments

Popular posts from this blog

How to fix error B200 on canon Printers

MAJ11/06/17 Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below: Solution 1 : Disconnect the power cable from the printer. Wait 1 hour. Connect the power cable Solution 2 : Check and Clean Head contact pin condition of the carriage unit Check Cable connection especially the carriage FFC Solution 3 : Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left. Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on Solution 4 : Unplug the power cable. Open the printer Push the whole print head mechanic to the center While the printer still open, plug the power and turn it ON.  When the printhead still moving and is going to the very LEFT, close the cover.  Wait until its boot up.  Solution 4a: Take out all of the ink cartridges Lift up the gr

How to solve error code 006 with Canon Service Tool V3400

MAJ 25/08/17 The Service Tool V3400 allow to reset the counter of some Canon printers. For the error code 006 , try this : Solution 1: Check your cartridges: an empty cartridge can lead to error 006 Solution 2 : After you avec clicked on "Main", wait a few minutes.  If the error still here, restarts the Service Tool Solution 3 : Close the service tool Disconnect the USB cable from the printer After 10 seconds, plug back the cable to the printer On Windows, click next when appears "New device" Open the service tool

How to solve error B204 on Canon Maxify printers

The error B204 could happen after a cartridge replacement. First of all, when installing, remove the cartridges from the plastic package, but do not drill any plastic membranes, as this will cause this error when placing the cartridge. The error may also appear if you change a completely empty cartridge: when installing a full cartridge, the printer enters a cleaning cycle, but the printhead has not yet received ink from the newly inserted cartridge. Here are some tips to cancel this error B204:: Solution 1: Remove the cartridges Power the printer for 2 minutes Switch on the printer Install the cartrdiges Solution 2: Switch on the printer Unplug  the power cable Open the cover Move the print head carriage manually to the usual place where it goes for the cartridge change (If the printhead carriage is not movable, reconnect and then turn on the printer, then unplug it again when the head carriage is in the moving position). Change the cartridges. Close the fr